bird does not install route to the kernel

[Volodymyr Samodid]

Here they are


R0

router id 198.51.100.10;

protocol kernel {
         scan time 60;
         import all;
         export all;   # Actually insert routes into the kernel routing 
table
}

protocol device {
         scan time 60;
}

protocol ospf TEST_OSPF {
         tick 2;
         rfc1583compat yes;
         import all;
         export all;
         ecmp yes;
         merge external;
         area 0.0.0.0 {
                 interface "eth0" {
                   stub yes;
                 };
                 interface "eth1" {
                   rx buffer large;
                 };
         };
};


R1

router id 198.51.100.11;

protocol kernel {
         scan time 60;
         import all;
         export all;   # Actually insert routes into the kernel routing 
table
}

protocol device {
         scan time 60;
}

protocol ospf TEST_OSPF {
         tick 2;
         rfc1583compat yes;
         import all;
         export all;
         ecmp yes;
         merge external;
         area 0.0.0.0 {
                 interface "eth0" {
                   rx buffer large;
                 };
                 interface "eth1" {
                   rx buffer large;
                 };
         };
};





On 08/29/2016 12:55 PM, Baptiste Jonglez wrote:
> Please show your configuration, especially the kernel protocol.  You need
> an appropriate export filter.
>
> On Thu, Aug 25, 2016 at 05:22:33PM +0300, Volodymyr Samodid wrote:
>> Hi community,
>> i played with bird6 and ospf3 and faced with issue.
>> In my schema bird does not install route to the kernel, but propagates route
>> to another ospfv3 routers. That leads to routing loop.
>>
>> Here is simple schema:
>>
>> eth0 ------- R0 ------- eth1 ------- bridge ------ eth0 ------- R1
>>
>> ospfv3 made  adjacency
>>
>> R0
>> bird> show ospf neighbors
>> TEST_OSPF:
>> Router ID       Pri          State      DTime   Interface  Router IP
>> 198.51.100.11     1     Full/BDR        00:34   eth1
>> fe80::602c:e2ff:fe96:9c41
>>
>> R1
>> bird> show ospf neighbors
>> TEST_OSPF:
>> Router ID       Pri          State      DTime   Interface  Router IP
>> 198.51.100.10     1     Full/DR         00:34   eth0
>> fe80::88e0:e3ff:fe08:7842
>>
>>
>> Now add ipv6 address to eth1 on R0
>>
>> R0# ip a add 2001:DB8::1/64 dev eth1
>>
>> on R1, got next
>>
>> bird> >>> TEST_OSPF > added [best] 2001:db8::/64 dev eth0
>> bird> show route
>> 2001:db8::/64      dev eth0 [TEST_OSPF 13:58:11] * I (150/10)
>> [198.51.100.11]
>>
>> R1# ip -6 ro s
>> fe80::/64 dev eth0  proto kernel  metric 256  pref medium
>>
>> added ipv6 address to eth0 on R0
>>
>> R0# ip a add 2001:DB8:1::1/64 dev eth0
>>
>> on R1
>> bird> >>> TEST_OSPF > added [best] 2001:db8:1::/64 via
>> fe80::88e0:e3ff:fe08:7842 on eth0
>>>>> kernel1 < added 2001:db8:1::/64 via fe80::88e0:e3ff:fe08:7842 on eth0
>> bird> show route
>> 2001:db8::/64      dev eth0 [TEST_OSPF 13:58:11] * I (150/10)
>> [198.51.100.11]
>> 2001:db8:1::/64    via fe80::88e0:e3ff:fe08:7842 on eth0 [TEST_OSPF
>> 14:05:31] * I (150/20) [198.51.100.10]
>>
>> R1# ip -6 ro s
>> 2001:db8:1::/64 via fe80::88e0:e3ff:fe08:7842 dev eth0  proto bird metric
>> 1024  pref medium
>> fe80::/64 dev eth0  proto kernel  metric 256  pref medium
>>
>> R1## ip monitor route
>> 2001:db8:1::/64 via fe80::88e0:e3ff:fe08:7842 dev eth0  proto bird metric
>> 1024  pref medium
>>
>> I can add such route manual.
>> R1# ip ro add 2001:db8::/64 dev eth0

-- 
С уважением,
Самодед Владимир
SVAJ-RIPE|SVA88-UANIC